
Warm brick color held in place for years
Brick Paver Sealing in Seminole, FL
Call (727) 619-2341 for a free estimate to seal brick pavers at your Seminole home.
- Brings out deeper paver color
- Fresh joint sand helps lock pavers in place
- Gives weeds less room to grow
- Makes the surface easier to keep clean
- Free estimate, no obligation
Request a Free Estimate
Free, no obligation.
Who can seal brick pavers at my home in Seminole?
A local contractor can seal brick pavers at your Seminole home, and a reply comes within 1 business day, usually much sooner. The estimate is free and booking is up to you. Reach out by calling (727) 619-2341.
Brick has a warmth that other pavers do not, and it shows every green patch and bare joint. Sealing keeps that color rich, helps hold the joint sand and makes a rinse enough for most dirt. The catch is that brick is not one material, so the first job is finding out what you have. Tell the contractor what you know about the pavers when you request a free estimate.
Is my brick clay or concrete, and does it matter for sealing?
It matters a great deal. Real clay pavers are fired at almost 2000 degrees, and the Brick Industry Association says the color runs all the way through, so they do not fade and need no sealer. Most clay units exceed 10,000 psi in strength. Many brick looking driveways are concrete pavers pressed into a brick pattern, and those do fade and do take sealer. For help telling which you have, call (727) 619-2341.
Age and source count too. A paver installer, an older invoice or a spare stone in the garage can tell you the maker. If you cannot tell, a contractor can check how the stone takes water and where color is only a surface layer. Send photos with your estimate request: request a free estimate.

Which areas near Seminole can get brick paver sealing?
Should brick pavers get a penetrating sealer or a film?
The choice shapes how the brick ages. A film sealer sits on top and gives the wet look. A penetrating sealer soaks into the pores and leaves the surface close to natural. A Hillsborough County company warns that trapped ground moisture under a film can turn brick white and cloudy, and says only stripping fixes it. A Seminole company uses a penetrating type for marble and travertine for the same reason. Ask which type is planned and why when you request a free estimate.
Unilock adds that sealers are not interchangeable, so a product made for concrete may not suit brick or stone. It also says a sealer with strong UV and salt resistance helps in coastal Florida. Pinellas County is a peninsula with 587 miles of coastline, so salt air reaches well inland. To go over the options, call (727) 619-2341.
What does Seminole weather do to brick pavers?
Brick is tough, but Seminole is damp. The city sits 3 feet above sea level and wraps part of Lake Seminole, so shaded brick near the water stays wet and grows algae sooner, as a Seminole company notes for lakefront lots. Heavy summer rain washes sand from the joints, and weeds follow. Belgard suggests a granular weed preventative between pavers and keeping the joints topped off so the base does not erode. Mention any green or sunken spots when you request a free estimate.
Algae in shade
Shaded brick near the lake or under oaks stays damp and turns slick on steps.
Salt air
Peninsula air carries salt inland, and a sealer with salt resistance helps, per Unilock.
Washed out joints
Storm rain pulls sand out, so joints are refilled before any sealer goes on.
Leaf stains
A Tampa Bay guide says live oak leaves and acorns stain unsealed or under-sealed pavers.
How does the brick paver sealing process work?
The process follows the same arc on every job, with brick specific cautions. A walk-through comes first, then cleaning, drying, new joint sand and the coat. For details on your brick, call (727) 619-2341.
1. Identify the brick
Clay or concrete, old coat or bare. The answer sets the sealer and the wash method.
2. Gentle wash
Unilock says to use a fan nozzle at about 30 degrees from 12 inches and to avoid wire brushes.
3. Treat the stains
Rust, algae and oil each get a cleaner made for them, tried on a hidden brick first.
4. Dry fully
Unilock says a few hours in warm sun, or about a day in cool shade, before any product goes on.
5. Sand and seal
Quartz sand is swept into the joints, then the sealer is applied in thin passes at the listed coverage.
6. Cure
A Seminole company says 24 hours off foot traffic, 48 to 72 hours for a full cure.
What does sealing brick pavers cost in Seminole?
No source read for this site gives a brick only rate, and the Tampa Bay cost guide says so itself. The table builds the figure from published pieces: the full clean, re-sand and seal range, the sealer material and the lines that are not priced. A Seminole company gives $1.00 to $1.75 per square foot. To turn that into a figure for your brick, request a free estimate.
Stripping an old film is the item most likely to move the price. A Hillsborough County company calls it labor intensive and costly, and it publishes no rate. Tint is an extra on the Seminole page, again with no figure. Look at the paver sealing guide for general ranges, or the service area list.
| Piece of the job | Published figure | Where it comes from |
|---|---|---|
| Clean, re-sand and seal together | $1.00 to $1.75 per sq ft | A Seminole paver company's page |
| Wider regional range | $1.25 to $2.50 per sq ft | A Tampa Bay paver cost guide |
| Example 400 sq ft brick walk and patio | $400 to $700 | Seminole range applied to 400 sq ft |
| Example 800 sq ft brick driveway | $800 to $1,400 | Seminole range applied to 800 sq ft |
| Sealer material | $80 to $150 a gallon | Unilock, covering 80 to 150 sq ft a gallon |
| Stripping, tint, brick surcharge | Not published | Both pages say extras are priced on the quote |
Prices come only from the pages named. No page gives a per-square-foot rate for brick alone, so this table breaks the job into the pieces that are published and marks the rest as not published.

How often should brick pavers be sealed in Seminole?
Every three to five years is the range from both Unilock and Belgard, and a Seminole company says every 2 to 3. Belgard sets a ceiling of once every three years and two applications in all. Clay brick that needs no sealer for color may only need one coat for joint sand and stain protection. For a reading on yours, call (727) 619-2341.
Will sealing fix brick that has settled or sunken?
No. Unilock says sealing will not repair drainage or base problems, so a settled spot has to be lifted and relaid first. Brick with a lip or a dip also traps water, which is how algae and film problems begin. Ask the contractor to flag every low spot before the price is final. Raise it when you request a free estimate.
Can I seal new brick pavers right away?
Not for a while. Unilock says to wait 60 to 90 days after installation, because efflorescence can take 2 to 3 months and sometimes a year to fade. Belgard sets 30 days as the minimum for new pavers and says a non film forming sealer can follow sooner. Share the date it was laid when you request a free estimate.
What do sealed brick pavers look like in Seminole?








Why hire a local contractor for brick paver sealing?
A contractor who works in Pinellas County has seen how humid summers, lake shade and salt air treat brick. Seminole grew from 7,297 housing units in 2000 to 11,216 in 2020, so older brick and newer brick often share a block. Each calls for its own plan. To get started, call (727) 619-2341.
Local knowledge
Heat in the low 90s, heavy summer rain and damp ground are everyday conditions here.
Plain price
A written quote that names the product, the coverage and each extra.
No pressure
The estimate is free and you can take your time. Ask about the contractor standards before you sign.
Fair comparison
Published Tampa Bay ranges give you something to check a bid against.
Want brick pavers that keep their warm color?
Tell a contractor what the brick looks like and where the green patches are. Someone gets back to you in 1 business day at the outside, usually much sooner.
Free, no obligation
What do Seminole homeowners ask about brick paver sealing?
What should concrete pavers be sealed with?
A water based acrylic or urethane sealer is the common choice for concrete pavers, and a penetrating sealer suits stone and some brick. Unilock says sealers are not interchangeable, so a product for concrete may not suit clay or natural stone. Ask the contractor to name the sealer and say why it fits.
Can I use Dawn dish soap to clean my pavers?
A mild detergent is what Unilock mentions for washing, and rinsing matters. Orange rust, green algae and oil each need a cleaner made for that stain, tried on a hidden corner first. Wire brushes are out, since Unilock says they can leave metal that rusts on the surface.
How much does it cost to install pavers in Florida?
A paver install price is outside what this page can say, because no source read for this site gives one. A sealing quote is a separate job and a separate price. If you plan to replace brick, get the installer to quote it by itself.
How often should pavers be resealed in Florida?
Unilock and Belgard say every three to five years, and a Seminole company says 2 to 3. Belgard says no more than once every three years and no more than two applications overall. Water that sinks in instead of forming beads tells you the coat is spent. For a check, call (727) 619-2341.
Which sealer suits brick pavers in Florida?
It depends on the brick. Unilock says a sealer with strong UV and salt resistance helps in coastal Florida. A Hillsborough County company says film sealers can trap ground moisture and turn brick white, so many choose a penetrating type that soaks in. Ask for the product name when you request a free estimate.
Do clay brick pavers need to be sealed at all?
Often not for color. The Brick Industry Association says clay pavers are fired through the body, do not fade and need no sealer. Many people still seal to hold joint sand and make washing easier. Concrete pavers in a brick pattern do fade, so know which you have.
What is the average cost to seal pavers in Florida?
A Seminole company publishes $1.00 to $1.75 per square foot to clean, re-sand and seal. A Tampa Bay cost guide shows $1.25 to $2.50 and lists nothing for brick or stripping. For 800 square feet the Seminole math is $800 to $1,400. For your brick, call (727) 619-2341.
Why did my brick pavers turn white after sealing?
Trapped moisture is the usual cause. Unilock says a whitish film comes from moisture caught under the coat, from too much product, or from sealing over an incompatible earlier product. A Hillsborough County company says film sealer over wet ground can turn brick white and cloudy, and that stripping is the fix.
Can old brick pavers be sealed again without stripping?
Only if the old coat is sound. A coat that has peeled, clouded or gone patchy usually has to come off first, which is slow and pricey work. A small test area shows whether new product bonds. To have a contractor look at yours, request a free estimate.
Ready to protect your brick pavers?
Phone a contractor or send the short form. Pricing is free to ask for, and booking is optional.
Free, no obligation
